TASI656 Digital Salt Meter Operating Instructions

Precautions

When the test rod is in the measuring salt solution, do not turn on the power, so as not to cause measurement errors and inaccurate readings.

Salt concentration specification

Range: 0.1% to 10.0%

Temperature compensation: -5°C to 60°C (automatic)

Accuracy:

0% to 0.9% (± 0.1)

1.0% to 1.9% (± 0.2)

2.0% to 2.9% (± 0.3)

3.0% to 4.9% (± 0.5)

5.0% to 5.9% (± 0.7)

6.0% to 7.9% (± 1.0)

8.0% to 10.0% (± 1.5, depending on the measurement method)

Temperature specification

Sensor: Thermistor

Range: -20°C to 60°C or -4°F to 140°F

Resolution: 0.1°C / 0.1°F

Accuracy:

±0.5°C at 0°C to 45°C

±1°C at -20°C to 0°C and 45°C to 60°C

±1°F at 32°F to 113°F

±2°F at -4°F to 32°F and 113°F to 140°F

General Specifications

Accuracy:

Standard accuracy guaranteed at 23°C±5°C (74°F±41°F), phase

Relative humidity is less than 75%

Temperature Coefficient:

When the operating ambient temperature is >28°C or <18°C, for every 1°C increase or decrease,

Specification increase is ±0.2% of reading or ±0.2°C, whichever is greater

Operating environment:

0°C to 50°C (32°F to 122°F) with relative humidity less than 70%

Storage temperature:

-20°C to 60°C (-4°F to 140°F) with relative humidity less than

80%, except battery.

pH electrode: 0°C to 80°C (32°F to 176°F)

Battery: 4.5V (three 1.5V batteries AAA size UM-4 R03)

Battery life: about 100 hours for carbon-zinc batteries

Low voltage indication:

When the battery voltage is lower than the operating voltage, the LCD will display " "

Dimensions: 15.1 cm(L) x 4.8 cm(W) ​​x 2.6 cm(H)

Teans TASI656 Digital Salt Meter Weight: 135 grams (including battery)

button

1. "MEAS":

按下“MEAS”键启动盐份计并开始准备量测，再按下“MEAS”关闭电源。

2. “RED”:

二种量测模式，“单次量测”和“间隔量测”。单次量测: “间隔量测时间”设定小于 2 秒时。在此量测模式下，每按下“RED”键就自动量测一次，并且 BEEP 会发出“哔”警示一声。间隔量测: 依“间隔量测时间”來决定多久自动量测一次。按下“RED”键则开始量测，依设定之“间隔量测时间”重新显示讀值，并且 BEEP会发出“哔”警示声，再按一下“RED”键则停止量测，BEEP 也停止警示声。

3. “MODE” ，“ ”  和 “ ”:

3.1  设定量测模式的间隔量测时间:

3.1.1 按“MODE” 键进入设定功能，LCD 右上显示“SET”，和 LCD 中下显示“SEC”或“cc”。

3.1.2 按“RED”键选择“SEC”和“cc”。设定为“SEC”。

3.1.3 按“▲”及“▼”设定所需之间隔量测之时间。长按“▲” 、“▼”可使设定值快速增加或减少。间隔时间最大为 60.0 分钟。

3.1.4 若设定为“001”秒，则设定为“ManualMode”。(參考“RED”功能說明)

3.1.5 按下“MODE”键來决定你的设定或者再重新设定。

3.2  设定量测盐重量的水溶液容量：

3.2.1 按“MODE” 键进入设定功能，LCD 右上显示“SET”，和 LCD 中下显示“SEC”或“cc”。

3.2.2 按“RED” 键选择“SEC” 和“cc”。设定为“cc”。

3.2.3 按“▲”及“▼”设定所需之间隔量测之时间。长按“▲”及“▼”可使设定值快速增加或减少。间隔时间最大为 1999cc。

3.2.4按下“MODE” 键來决定你的设定或者再重新设定。

4. “AVG”  和 “ ”:

平均功能:能记錄 9 点盐液浓度量测值，记錄方式如下: →0 → 1 → 2 → 3→ 4 → 5 → 6 → 7→ 8→ 9→ 0按下“AVG”键会将所量测的值作平均显示，平均值的资料显示只有在量测资料超过 2 笔才会动作。

5. APO  功能:

按住“AVG”键 2 秒以上启动或关闭 APO 功能。若 30 秒之内未操作盐份计，将自动关机，若有操作盐份计，则 APO 时间重新计算。

6. “°C/°F”  和 “ ”:

设定温度单位:按下“°C/°F” 键來改变温度量测单位°C 或°F。

设定盐液单位:按住“°C/°F”键 2 秒以上來改变盐液单位“%”和“g”(grams)。预设单位为“%”。

盐液浓度(%) = (盐的重量) ÷ (溶液的重量) ×100%

盐的重量(g) = 盐液浓度 (%) × (溶液的重量)

维护事项

After measuring the salt solution, be sure to rinse the test stick with clean water, and wipe the test stick clean before putting on the protective cover. If the test stick is not cleaned after measurement, it will be damaged for the next time measurement results in large errors.

After use, be sure to wash the test stick with clean water, wipe it clean with a soft cloth, and then put the protective cover on.

battery replacement

1. If the “ ” symbol appears on the LCD  , it means that the battery power is insufficient. Please replace the battery to maintain the accuracy of the test.

2. Loosen one screw on the battery cover of the thermometer, take off the battery cover, and replace it with four 1.5V (SIZE AAA) UM-4 R03 batteries.

3. When the TASI600 / 601 dual-input K thermocouple wire digital thermometer is not in use for a long time, please take out the battery from the thermometer and avoid storing it in a place with high temperature and high humidity.

clean

Periodically use a soft damp cloth dipped in a neutral detergent to gently wipe the case, do not use emery cloth or solvents with dissolving power to wipe.