Germany Erichsen 295/V Paint film adhesion Cross Hatch Cutter set 11 teeth/1mm

Erichsen 295/V film adhesion Cross Hatch Cutter number of teeth 11, tooth spacing 1mm, suitable for film thickness environment 0~50μm, instrument material stainless steel, handle material plastic, knife head material stainless steel, blade number 2.

$1078.00/set

PromotionLoading...

Coupon

Model：

erichsen 295/V

Erichsen

Contact

Details SPEC Con CAT

Erichsen erichsen 295/V Cross-cut knifeSPEC

Erichsen erichsen 295/V Cross-cut knifeDetails

Erichsen erichsen 295/V Cross-cut knifePacking list

SKU: NB013716

Number of teeth: 11 teeth

Tooth spacing: 1mm

Applicable film thickness environment: 0~50μm

Instrument material: stainless steel

Handle material: plastic

Cutter head material: stainless steel

number of blades: 2

erichsen 295/V

Cross-cut knife

The erichsen295 paint cross-hatch knife meets all cross-hatch test standards. It consists of a plastic handle and a cutter head mounted on it. The cutter head can be adjusted to the most comfortable position for the operator. Different types of cutter heads are available and a tape according to EN ISO 2409 is available.

The erichsen 295 cross-cutting instrument is supplied complete, including a cutter head mounted on a plastic handle. Comes in a sturdy plastic carrying case and also contains a nylon brush and a 2.5x magnifying glass. For the 295/III single-edged blade, a folding rule is also provided. The instrument also comes with manufacturer's certificate M.

Comparison of parameters of Erichsen cross hatcher series

standard	Film thickness	Tool number x spacing (mm)	model	Item number
ISO 2409 EN ISO 2409	up to 60Î¼m 60~120Î¼m 120~250Î¼m	6 x 1	295/I	0019.01.31
		6 x 1	295/II	0019.02.31
		6 x 2	295/II	0019.02.31
		6 x 3	295/III or 295/VII	0019.03.31 (0019.07.31)

ASTM D 3359	up to 50Î¼m 50~125Î¼m	11x1	295/V	0019.05.31
ASTM D 3359	up to 50Î¼m 50~125Î¼m	6x2	295/II	0019.02.31

JIS K 5400 JIS K 6894	up to 60Î¼m 60~120Î¼m Greater than 120Î¼m	11x1	295/V	0019.05.31
		6x2	295/II	0019.02.31
		6x3	295/III or 295/VII	0019.03.31 (0019.07.31)

SNV 37111	up to 60Î¼m Greater than 60Î¼m	8x1	295/III	0019.03.31
SNV 37111	up to 60Î¼m Greater than 60Î¼m	8x2	295/III	0019.03.31

VDA 621-411	up to 60 Î¼m 60~120 Î¼m Greater than 120 Î¼m	6x1	295/I	0019.01.31
		6x2	295/II	0019.02.31
		6x3	295/III	0019.03.31 (0019.07.31)

ECCA ² )	up to 50 Î¼m Greater than 50 Î¼m	11x1	295/V	0019.05.31
ECCA ² )	up to 50 Î¼m Greater than 50 Î¼m	2x5	295/IV	0019.04.31

ISO 2409-1972 BS 3900:E NFT 30-038	Agreement	11x2	295/VI	0019.06

1.After 1994, the European standard ENISO2409 replaced the national standards DIN53151, BS3900: E6, NFT30-38, NEN5337 and SIS184172.

2. After the cross-hatch test, you can also do a deep drawing test (ENISO1520). Deep drawing experiments can be completed with the following instruments:

ERICHSEN cupping Tester, model 200, 202, 202C or 204

Impact test device 304ECCA compliant with ASTM D3359

3. For soft substrates.

4. For hard substrates.

FAQ

QDetermination of water-based interior-wall Coating adhesion, is this cross-cutting knife suitable?

A This model is suitable for the determination of water-based inner and outer wall Coating adhesion in architectural coatings. The cross-cut test is mainly carried out with knives, and the firmness of the Coating to the substrate is judged according to the number of squares of the film peeling. Use a sharp blade and a scale steel ruler to cut 11 cuts with a distance of 1mm in the vertical and horizontal directions of the test plate, and the vertical and horizontal cuts intersect into 100 squares. So it is applicable.

QIs this the cross-cutting knife mentioned in GB/T9286?

A OK

Knowledge

Standard

Filter Brand Store Contact