United States

RDS 7 #3/8 "Proofing rod 16.0μm Applicator rod

SE
The production process is formed, the wet film thickness is 16.0μm, the diameter is 9.52mm, the Total length is 400mm, the Spreader width is 300mm, and the material is stainless steel.
$161.00/piece
PromotionLoading...
Coupon
Model：
Certificate
Contact
Details SPEC Con VIDEO CAT OI
Similar products

RDS 7# 3/8" Applicator rod 3/8 "SPEC

RDS 7# 3/8" Applicator rod 3/8 "Details

RDS 7# 3/8" Applicator rod 3/8 "Packing list

SKU
NB033700
Production process
Formed
WFT
16.0μ m
diameter
9.52mm
Total length
400mm
Application width
300mm
material
stainless steel
7# 3/8"
Applicator rod 3/8 "
The production process is formed, the wet film thickness is 16.0μm, the diameter is 9.52mm, the Total length is 400mm, the Spreader width is 300mm, and the material is stainless steel.
RDS 7 #3/8 "Proofing rod 16.0μm Applicator rod Picture

Product description

RDS 7# forming type color scraping rod adopts the same extrusion coating process as OSP, and the effect of coating film is the same as that of No. 7 wire-wound coating rod, but the amount of coating loss may different. The diameter of the rds film scraping rod is 9.5mm, which is the rod diameter that domestic (CN) users are more accustomed to choosing, and it can be matched with a small coating machine for coating. The wet film thickness of No. rds7 color bar coating is 16.0μm.

RDS coating Rods Figure 1

RDS coating Rods Figure 2

RDS coating Rods Figure 3

RDS coating Rods Figure 4

RDS coating Rods Figure 5

RDS coating Rods Figure 6

RDS coating Rods Figure 7

RDS coating Rods Figure 8

RDS coating Rods Figure 9

RDS coating Rods Figure 10


FAQ
QWhat is the difference between the same 3/8 "diameter round Mayer-Rod and this molding rod? Can it be replaced?
A The main difference between the Mayer-Rod and the molding rod is the different process of groove formation. The wire rods of the same specification and different processes can be replaced by each other, and the wet film thickness is the same. The difference is because the groove shapes of the two are different (the molding is U-shaped groove, and the winding wire is V-shaped groove). The calculation of the Spreader amount is different, and the relative molded Spreader amount will be more. There is no difference for laboratory use.
QMoulding rod is better for winding or extrusion?
A In theory, the Moulding effect is the same. The extrusion U-groove is relatively easy to clean, but it requires high asperity on the inner wall of the groove. The winding follows the Mayer principle, and the scraping is smoother. If used for pre-production Measurement, the extrusion Spreader is larger than the winding. The same film thickness was prepared in the laboratory, and the effect was the same.
QCan this cable stick be matched with a Film Applicator?
A Whether it can be matched with the Film Applicator depends on the film width of the Film Applicator. Most Film Applicator film widths on the market are less than 40cm, and the rod diameter is less than 10mm, so it is suitable. But if the Film Applicator is specially customized, or the width exceeds 40cm, you need to choose a longer rod. For customization, please consult NBchao.
QCan this scraper be coated with UV Gloss oil?
A OK
QDo you support customization? Such as wet film thickness and length?
A Spreader rod length and main rod diameter support customization, but wet film thickness RDS has provided dozens of specifications covering more than 200 microns, and in principle does not accept customization.
Knowledge
Standard
Filter Brand Store Contact