RDS 9 #3/8 "Molded Mayer Rod 20.6 μm inks Proofing rod
SEProduction process is formed, wet film thickness 20.6 μm, diameter 9.52mm, Total length 400mm, Spreader width 300mm, material stainless steel.
$161.00/piece
PromotionLoading...
Coupon
Model：
9# 3/8"
Similar products
-
RDS #9 Mayer Rods WFT 20.6 μm length 400mm$ 161.00SE -
Japan OSP-20/400 coating rod WFT 20μm coating bar film 400mm$ 172.00SE -
RDS #9, Formed Mayer Rods Grooved Rods Applicator rod$ 155.00SE -
RDS #9 wire-wound Mayer Rods experimental wire-wound drawdown Bar 6.35mm diameter$ 155.00SE -
RDS #9 wire-wound Mayer Rods 1/2 "Film thickness 20.6μm$ 179.00SE
RDS 9# 3/8" Applicator rod 3/8 "SPEC
RDS 9# 3/8" Applicator rod 3/8 "Details
RDS 9# 3/8" Applicator rod 3/8 "Packing list
- SKU
- NB033702
- Production process
- Formed
- WFT
- 20.6µm
- diameter
- 9.52mm
- Total length
- 400mm
- Application width
- 300mm
- material
- stainless steel
9# 3/8"
Applicator rod 3/8 "
Production process is formed, wet film thickness 20.6 μm, diameter 9.52mm, Total length 400mm, Spreader width 300mm, material stainless steel.
Product description
RDS Meyer rods are imported products from the United States, and have more than 80 years of experience in CHINA. Its laboratory ink scraping rods are widely used in CHINA, involving 50 or 60 sub-sectors. The rds formed Meyer rod adopts a cold extrusion process, which has the advantage of being easier to clean. The coating film thickness of No. 9 bar was 20.6 μm, and the coating width was 30 cm.
FAQ
QWhat does 3/8 mean?
A
The diameter of the rod is 3/8 inch, which is about 9.5mm.
QWhat is the difference between the same 3/8 "diameter round Mayer-Rod and this molding rod? Can it be replaced?
A
The main difference between the Mayer-Rod and the molding rod is the different process of groove formation. The wire rods of the same specification and different processes can be replaced by each other, and the wet film thickness is the same. The difference is because the groove shapes of the two are different (the molding is U-shaped groove, and the winding wire is V-shaped groove). The calculation of the Spreader amount is different, and the relative molded Spreader amount will be more. There is no difference for laboratory use.
QMoulding rod is better for winding or extrusion?
A
In theory, the Moulding effect is the same. The extrusion U-groove is relatively easy to clean, but it requires high asperity on the inner wall of the groove. The winding follows the Mayer principle, and the scraping is smoother. If used for pre-production Measurement, the extrusion Spreader is larger than the winding. The same film thickness was prepared in the laboratory, and the effect was the same.
QCan this cable stick be matched with a Film Applicator?
A
Whether it can be matched with the Film Applicator depends on the film width of the Film Applicator. Most Film Applicator film widths on the market are less than 40cm, and the rod diameter is less than 10mm, so it is suitable. But if the Film Applicator is specially customized, or the width exceeds 40cm, you need to choose a longer rod. For customization, please consult NBchao.
QDo you support customization? Such as wet film thickness and length?
A
Spreader rod length and main rod diameter support customization, but wet film thickness RDS has provided dozens of specifications covering more than 200 microns, and in principle does not accept customization.
Knowledge
Standard