United States

RDS 10 #3/8 "Molded Wet Rubber Scraper 22.9μm Glue Stick

SE
The production process is formed, the wet film thickness is 22.9μm, the diameter is 9.52mm, the Total length is 400mm, the Spreader width is 300mm, and the material is stainless steel.
$161.00/piece
PromotionLoading...
Coupon
Model：
Certificate
Contact
Details SPEC Con VIDEO CAT OI
Similar products

RDS 10# 3/8" Applicator rod 3/8 "SPEC

RDS 10# 3/8" Applicator rod 3/8 "Details

RDS 10# 3/8" Applicator rod 3/8 "Packing list

SKU
NB033703
Production process
Formed
WFT
22.9pm
diameter
9.52mm
Total length
400mm
Application width
300mm
material
stainless steel
10# 3/8"
Applicator rod 3/8 "
The production process is formed, the wet film thickness is 22.9μm, the diameter is 9.52mm, the Total length is 400mm, the Spreader width is 300mm, and the material is stainless steel.
RDS 10 #3/8 "Molded Wet Rubber Scraper 22.9μm Glue Stick Picture

Product description

The American rds forming wet glue scraper is used for low-viscosity glue, heat-sensitive adhesive and other experimental coating films. The thickness of the coating film is 22.9 μm, and the coating width is 30 cm. The material is high-grade wear-resistant stainless steel, and the process is molding. RDS10# glue stick has different diameters, among which 3/8 diameter is more in line with the habits of domestic (CN) users, so it is also a popular series. There are also two diameters of 1/2'' and 1/4''.

RDS coating Rods Figure 1

RDS coating Rods Figure 2

RDS coating Rods Figure 3

RDS coating Rods Figure 4

RDS coating Rods Figure 5

RDS coating Rods Figure 6

RDS coating Rods Figure 7

RDS coating Rods Figure 8

RDS coating Rods Figure 9

RDS coating Rods Figure 10


FAQ
QWhat is the difference between the same 3/8 "diameter round Mayer-Rod and this molding rod? Can it be replaced?
A The main difference between the Mayer-Rod and the molding rod is the different process of groove formation. The wire rods of the same specification and different processes can be replaced by each other, and the wet film thickness is the same. The difference is because the groove shapes of the two are different (the molding is U-shaped groove, and the winding wire is V-shaped groove). The calculation of the Spreader amount is different, and the relative molded Spreader amount will be more. There is no difference for laboratory use.
QMoulding rod is better for winding or extrusion?
A In theory, the Moulding effect is the same. The extrusion U-groove is relatively easy to clean, but it requires high asperity on the inner wall of the groove. The winding follows the Mayer principle, and the scraping is smoother. If used for pre-production Measurement, the extrusion Spreader is larger than the winding. The same film thickness was prepared in the laboratory, and the effect was the same.
QCan this cable stick be matched with a Film Applicator?
A Whether it can be matched with the Film Applicator depends on the film width of the Film Applicator. Most Film Applicator film widths on the market are less than 40cm, and the rod diameter is less than 10mm, so it is suitable. But if the Film Applicator is specially customized, or the width exceeds 40cm, you need to choose a longer rod. For customization, please consult NBchao.
QDo you support customization? Such as wet film thickness and length?
A Spreader rod length and main rod diameter support customization, but wet film thickness RDS has provided dozens of specifications covering more than 200 microns, and in principle does not accept customization.
Knowledge
Standard
Filter Brand Store Contact