United States

RDS 23 #3/8 "Grooved Rods Film Applicator 52.6μm Mayer Rods

SE
Formed, wet film thickness 52.6 μm, diameter 9.52mm, Total length 400mm, Spreader width 300mm, stainless steel material.
$161.00/piece
PromotionLoading...
Coupon
Model：
Certificate
Contact
Details SPEC Con VIDEO CAT OI
Similar products

RDS 23# 3/8" Applicator rod 3/8 "SPEC

RDS 23# 3/8" Applicator rod 3/8 "Details

RDS 23# 3/8" Applicator rod 3/8 "Packing list

SKU
NB033712
Production process
Formed
WFT
52.6µm
diameter
9.52mm
Total length
400mm
Application width
300mm
material
stainless steel
23# 3/8"
Applicator rod 3/8 "
Formed, wet film thickness 52.6 μm, diameter 9.52mm, Total length 400mm, Spreader width 300mm, stainless steel material.
RDS 23 #3/8 "Grooved Rods Film Applicator 52.6μm Mayer Rods Picture

Product description

RDS 23# 3/8" extruded wire rod Film Applicator has a film thickness of 52.6 microns, a rod diameter of 9.5mm, and a film width of 300mm. It is suitable for experimental film coating in ink, printing, packaging, paper and other fields .The Total length of the RDS wire rod Film Applicator is 400mm, which can be used for supporting the experimental film coating machine, and each end of the rod has a 50mm hand-holding part, which does not need a matching handle. The good stainless steel material of 304 makes it have a higher abrasion resistance.

RDS coating Rods Figure 1

RDS coating Rods Figure 2

RDS coating Rods Figure 3

RDS coating Rods Figure 4

RDS coating Rods Figure 5

RDS coating Rods Figure 6

RDS coating Rods Figure 7

RDS coating Rods Figure 8

RDS coating Rods Figure 9

RDS coating Rods Figure 10


FAQ
QWhat is the difference between the same 3/8 "diameter round Mayer-Rod and this molding rod? Can it be replaced?
A The main difference between the Mayer-Rod and the molding rod is the different process of groove formation. The wire rods of the same specification and different processes can be replaced by each other, and the wet film thickness is the same. The difference is because the groove shapes of the two are different (the molding is U-shaped groove, and the winding wire is V-shaped groove). The calculation of the Spreader amount is different, and the relative molded Spreader amount will be more. There is no difference for laboratory use.
QMoulding rod is better for winding or extrusion?
A In theory, the Moulding effect is the same. The extrusion U-groove is relatively easy to clean, but it requires high asperity on the inner wall of the groove. The winding follows the Mayer principle, and the scraping is smoother. If used for pre-production Measurement, the extrusion Spreader is larger than the winding. The same film thickness was prepared in the laboratory, and the effect was the same.
QCan this cable stick be matched with a Film Applicator?
A Whether it can be matched with the Film Applicator depends on the film width of the Film Applicator. Most Film Applicator film widths on the market are less than 40cm, and the rod diameter is less than 10mm, so it is suitable. But if the Film Applicator is specially customized, or the width exceeds 40cm, you need to choose a longer rod. For customization, please consult NBchao.
QDo you support customization? Such as wet film thickness and length?
A Spreader rod length and main rod diameter support customization, but wet film thickness RDS has provided dozens of specifications covering more than 200 microns, and in principle does not accept customization.
Knowledge
Standard
Filter Brand Store Contact