United States

RDS 46 #3/8 "photosensitive paste rod 105.2μm molded wire-wound drawdown Bar

SE
Production process is formed, wet film thickness 105.2μm, diameter 9.52mm, Total length 400mm, Spreader width 300mm, material stainless steel.
$161.00/piece
PromotionLoading...
Coupon
Model：
Certificate
Contact
Details SPEC Con VIDEO CAT OI
Similar products

RDS 46# 3/8" Applicator rod 3/8 "SPEC

RDS 46# 3/8" Applicator rod 3/8 "Details

RDS 46# 3/8" Applicator rod 3/8 "Packing list

SKU
NB033725
Production process
Formed
WFT
105.2μm
diameter
9.52mm
Total length
400mm
Application width
300mm
material
stainless steel
46# 3/8"
Applicator rod 3/8 "
Production process is formed, wet film thickness 105.2μm, diameter 9.52mm, Total length 400mm, Spreader width 300mm, material stainless steel.
RDS 46 #3/8 "photosensitive paste rod 105.2μm molded wire-wound drawdown Bar Picture

The RDS 46# 3/8" photosensitive paste wire rod is available in different processes of forming type and winding type, the coating thickness is 105.2μm, and each end of the rod has a 50mm handle part. This RDS46 rod is a molding process, which is an extrusion process to extrude a groove on a smooth rod, and the thickness of the coating film is controlled by the size of the groove. RDS coated wire rod is made of wear-resistant stainless steel, which has the advantages of continuous filament and easy cleaning. For precision instruments, it is necessary to pay attention to maintenance and care during the usual use process to ensure a longer service life.

RDS coating Rods Figure 1

RDS coating Rods Figure 2

RDS coating Rods Figure 3

RDS coating Rods Figure 4

RDS coating Rods Figure 5

RDS coating Rods Figure 6

RDS coating Rods Figure 7

RDS coating Rods Figure 8

RDS coating Rods Figure 9

RDS coating Rods Figure 10


FAQ
QWhat is the difference between the same 3/8 "diameter round Mayer-Rod and this molding rod? Can it be replaced?
A The main difference between the Mayer-Rod and the molding rod is the different process of groove formation. The wire rods of the same specification and different processes can be replaced by each other, and the wet film thickness is the same. The difference is because the groove shapes of the two are different (the molding is U-shaped groove, and the winding wire is V-shaped groove). The calculation of the Spreader amount is different, and the relative molded Spreader amount will be more. There is no difference for laboratory use.
QMoulding rod is better for winding or extrusion?
A In theory, the Moulding effect is the same. The extrusion U-groove is relatively easy to clean, but it requires high asperity on the inner wall of the groove. The winding follows the Mayer principle, and the scraping is smoother. If used for pre-production Measurement, the extrusion Spreader is larger than the winding. The same film thickness was prepared in the laboratory, and the effect was the same.
QCan this cable stick be matched with a Film Applicator?
A Whether it can be matched with the Film Applicator depends on the film width of the Film Applicator. Most Film Applicator film widths on the market are less than 40cm, and the rod diameter is less than 10mm, so it is suitable. But if the Film Applicator is specially customized, or the width exceeds 40cm, you need to choose a longer rod. For customization, please consult NBchao.
QDo you support customization? Such as wet film thickness and length?
A Spreader rod length and main rod diameter support customization, but wet film thickness RDS has provided dozens of specifications covering more than 200 microns, and in principle does not accept customization.
Standard
Filter Brand Store Contact