STIP-scan

Detect the content of ammonia nitrogen, the range is 0.05mg/L-50mg/L, no digestion is required, and the digestion Colorimetric integrated detection is used, which conforms to the HJ535-2009 standard.

Detect the Total nitrogen content, the range is 0.5mg/L-100mg/L (measured in sections), the digestion is carried out in a Water Bath at 125 ℃ for 30min, and the digestion Colorimetric integrated detection is adopted, which conforms to the EPA certification method.

Detect the content of hexavalent chromium, the range is 0.01mg/L-5mg/L (measured in sections), no digestion is required, the detection time is 10 to 15 minutes, and the digestion Colorimetric integrated detection is used, which conforms to the GB7467-87 standard.

Detection of iron content, the range is 0.01mg/L-50mg/L (measured in sections), no digestion is required, the detection time is 15 to 20 minutes, and the digestion Colorimetric integrated detection is used, which conforms to the HJ/T345-2007 standard.

The permanganate index (CODmn) was detected, the range was 0.1mg/L-10mg/L (measured in sections), the digestion was carried out in a Water Bath for 13min, and the digestion Colorimetric integrated detection was used, which conformed to the GB11892 standard.

Detection of Total phosphorus (TP) content, range 0.01-50 mg/L, using GB 11893-89 "Water quality, determination of Total phosphorus, ammonium molybdate Spectrophotometric method, spectra-trophotometry" detection method, built-in thermal printer, using digestion Colorimetric integrated tube.

At the same time, the parameters of four heavy metals, total chromium, hexavalent chromium, copper and zinc, were detected by digestion Colorimetric integrated tube, and imported cold Light source, Sensitivity was as high as 0.001mg/L.

The chemical oxygen demand (COD) value in water was measured, and two COD detection methods were built in, the ranges were 0-10000mg/L and 0-15000mg/L, respectively, and the digestion Colorimetric integrated tube Colorimetric was used.

Detect the Total phosphorus content in water quality, the range is 0.02mg/L-20mg/L (measured in sections), the digestion is carried out in a Water Bath at 125 ℃ for 30min, and the digestion Colorimetric integrated detection is used, which conforms to the GB11893 standard.

Detection of total chromium content, range 0.01-5 mg/L, using GB7466-87 detection method, built-in thermal printer, using digestion Colorimetric integrated tube.

Detect the concentration value of suspended solids, the range is 5mg/L-500mg/L (measured in sections), no digestion is required, the detection time is 1 to 2 minutes, and the imported cold Light source conforms to the "National Standard Weight Method" standard.

Detect the cyanide content, the range is 0.004mg/L-1mg/L (segmented determination), no digestion is required, and the digestion Colorimetric integrated detection is used, which conforms to the HJ484-2009 standard.

Detection of residual chlorine total chlorine content, the range is 0.1-10mg/L (measured in sections), no digestion is required, the detection time is 1 to 10 minutes, and the digestion Colorimetric integrated detection is used, which meets the standard of "TMB photometric method".

Detect the content of copper ions, the range is 0.05mg/L-10mg/L (measured in sections), no digestion is required, the detection time is 5 to 10 minutes, and the digestion Colorimetric integrated detection is used, which conforms to the standard of "Bicyclohexanone Oxalyl Dihydrazone Method".

Detect the total chromium content, the range is 0.01mg/L-5mg/L (measured in sections), the digestion is 30min in a Water Bath at 125 ℃, and the detection time is 45-55 minutes. The digestion Colorimetric integrated detection is used, which conforms to the GB7466-87 standard.

Detect the sulfide content, the range is 0.01mg/L-4mg/L (measured in sections), no digestion is required, and the digestion Colorimetric integrated detection is used, which conforms to the GB/T16489-96 standard.

Detect the fluoride content, the range is 0.02mg/L-10mg/L (segmented determination), no digestion is required, and the digestion Colorimetric integrated detection is used, which conforms to the HJ488-2009 standard.

Detect the content of silica, the range is 0.1mg/L-5mg/L (segmented measurement), no digestion is required, the detection time is 5 to 10 minutes, and the digestion Colorimetric integrated detection is used, which conforms to the "Silicon Molybdenum Blue Colorimetry" standard.

Detect the nitrite content, the range is 0.002mg/L-1mg/L (segmented determination), no digestion is required, and the digestion Colorimetric integrated detection is used, which conforms to the GB7493-87 standard.

Detection of ammonia nitrogen content, range 0.01-50 mg/L, using HJ535-2009 detection method, built-in thermal printer, using digestion Colorimetric integrated tube.

Detection of zinc content, the range is 0.05mg/L-15mg/L (segmented determination), no digestion is required, the detection time is 5 to 10 minutes, and the digestion Colorimetric integrated detection is used, which conforms to the "Xylenol Orange Spectrophotometric method, spec-trophotometry" standard.

Detect the content of phosphoric acid salt, the range is 0.02mg/L-20mg/L (segmented determination), without digestion, using digestion Colorimetric integrated detection, in line with HJ 670-2013 standard.

Detect Total nitrogen content, range 0.5-100mg/L, use persulfate oxidation method, built-in thermal printer, use digestion Colorimetric integrated tube, standard detection program Total nitrogen L and Total nitrogen H.

Detection of manganese content, the range is 0.04mg/L-5mg/L (measured in sections), no digestion is required, the detection time is 10 to 15 minutes, and the digestion Colorimetric integrated detection is used, which conforms to the GB11906-89 standard.

Detect the content of chlorine dioxide, the range is 0.05mg/L-10mg/L (measured in sections), no digestion is required, the detection time is 1 to 2 minutes, and the digestion Colorimetric integrated detection is used.