HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required

High-precision modular Spreader station structure, no air source, minimum gluing thickness 0.01mm, can be separated from the winding module, with quick-release plastic tank and electronic precision tension control function.

$5512.00/set

PromotionLoading...

Coupon

Model：

JTM-300

Certificate

HuiNuo

Chinese general agent

Contact

Details SPEC Con VIDEO CAT

HuiNuo JTM-300 Small continuous coaterSPEC

HuiNuo JTM-300 Small continuous coaterDetails

HuiNuo JTM-300 Small continuous coaterPacking list

SKU: NB050527

Coating Method: continuous scratch coating

Effective application width: ≤ 300mm, adjustable through baffle

Drawdown blade adjustment: manual adjustment

Spreader roller diameter: Ф50mm

Spreader thickness range: 0.01mm~2mm

Minimum gluing thickness: 0.01Mm (depending on the slurry, refer to the material requirements)

Coating surface density: ≤ +/- 1.5% (including substrate, excluding edge anomalies)

Coating Speed: 2~ 4.5M/min forward and reverse stepless transmission

Film Accuracy: +/- 0.003mm (depending on slurry, reference material requirements)

Regulator resolution: 0.001mm

Indication Display mode: digital display

Heating device: Chute heating

Heating mode: Heating rod

Temperature range: RT+~200℃

box Volume: About 0.5L

Width of guide roller: 300mm

substrate width: Max.300mm

Back roller diameter: Ф150mm

Reel diameter: 3 inches.

rewinding diameter: Max.Ф450mm

Applicable materials: hot-melt adhesive

Machine Power: 1050W

Host Power Supply: AC220V (single phase) 50Hz

Machine size: 1051*635*600mm

Machine Weight: About 120kg

JTM-300

Small continuous coater

Introduction

The continuous hot melt adhesive coating experimental machine is a modular assembly of high-precision modular coating station mechanism, with a separable winding module, which can be added as needed, and the whole machine is fully electrically controlled, without the need for an external air source. Continuous coating proofing or low-volume production of laboratory mini hot melt adhesive coaters. The hot melt pressure-sensitive adhesive can be directly applied to the heat-resistant substrate, or coated on the release paper and then the film transfer map can be applied to different surface materials, or the single-sided coating film of the curing module can also be added. Electronically controlled precision tension control, which can adapt to the needs of different materials. Such as paper, plastic model, metal film, etc.

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 1

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 2

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 3

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 4

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 5

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 6

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 7

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 8

HuiNuo JTM-300 Small continuous coater Roll-to-roll Film Applicator No air source required Figure 9

Configuration brief

(1) The whole machine is a high-precision modular coating station structure, which adopts modular assembly.

(2) Fully electric control, no external air supply required

(3) Use the dial indicator as the index head to accurately fine-tune the coating gap between the upper and lower rubber wheels to control the coating thickness.

(4) The minimum gluing thickness is0.01mm。 After the thickness is set, the downforce is provided by the electric actuator to prevent the gap from changing

(5) The maximum coating width is 300mm (effective coating width is 280mm). The width is adjusted by two pieces of PEEK baffles in the rubber groove. It can be coated and glued for unlimited length, and is automatically rewound.

(6) Forward and reverse stepless variable speed, coating speed: 4.5m/min (speed 2-4.5m/min adjustable), precision electronically controlled discharge reel can adjust the knob of the control panel, accurately change the discharge tension, and keep it continuously.

(7) Quick-release glue tank, the glue wheel and the rubber groove can be quickly disassembled and separated from the machine body to remove the residual glue.

FAQ

QI want to do hot-melt adhesive Spreader experiment, need a small equipment, what is recommended?

A HuiNuo JTM-300 small continuous coater is specially designed for hot-melt adhesive Spreader, all-electric control without external air source, Spreader thickness minimum 0.01mm, support unlimited length automatic winding, very suitable for laboratory proofing and small batch production.

QSpreader thickness control accuracy? Is easy to operate?

A The thickness control adopts the dial meter indexing head to fine-tune the gap, the resolution is 0.001mm, and the film accuracy is +/- 0.003mm. The electric push rod automatically maintains pressure and prevents the gap from changing, and there is a quick-release glue slot for easy cleaning. The operation is simple and worry-free.

QThe laboratory needs to do hot-melt adhesive Spreader experiment. Is there any verification equipment that can continuously Spreader?

A HuiNuo JTM-300 small continuous coater is specially designed for the laboratory, and the all-electric control does not require an external gas source, and the operation is simple. The minimum thickness of Spreader can reach 0.01mm, which is suitable for hot-melt adhesive Spreader experiments. The modular structure is easy to expand and the cost performance is high.

QCan this Spreader function be used for Spreader hydrocolloid dressings?

A Yes, JTM-300 supports hot-melt adhesive, gel, hydrocolloid dressing and other materials Spreader. It adopts a precision electronically controlled tension system, which can stably handle different substrates, and the heating range is RT +~ 200 ° C to ensure uniform hydrocolloid Spreader.

QHow to control the thickness of Spreader? Do you need to adjust it frequently?

A It uses the dial meter indexing head to fine-tune the Spreader gap, with an accuracy of 0.001mm. After setting, the electric push rod automatically maintains the pressure to prevent the gap from changing. The thickness range of Spreader is 0.01mm~ 2mm, and there is basically no need to adjust frequently after one setting, saving time and effort, suitable for long-term experiments.

Filter Brand Store Contact