HuiNuo JTM-02/300 Small roll-to-roll coater with heat curing High Accuracy Modular Spreader Station with 2m oven
JTM-02/300
HuiNuo JTM-02/300 Small continuous coater (with heat curing)SPEC
HuiNuo JTM-02/300 Small continuous coater (with heat curing)Details
HuiNuo JTM-02/300 Small continuous coater (with heat curing)Packing list
- SKU
- NB050651
- coating method
- continuous scratch coating
- Effective Spreader Width
- ≤ 300mm, adjustable through baffle
- coating method
- roller painting
- Spreader roller diameter
- Ф50mm
- Spreader Film thickness range
- 0.01mm~2mm
- Film thickness
- 0.01Mm (Depending on Stock, Reference Material Requirements)
- Coating Surface Density
- ≤ +/- 1.5% (including substrate, excluding edge anomalies)
- coating speed
- 2~ 4.5M/min forward and reverse stepless transmission
- Film accuracy
- +/- 0.003Mm (Depending on Stock, Reference Material Requirements)
- Regulator resolution
- 0.001mm
- Indication display
- digital display
- Heating device
- trough heating
- Heating method
- Heating rod
- Temperature range
- RT+~200℃
- box volume
- About 0.5L
- Drying area
- Length 2000mm * Width 300mm
- Drying temperature range
- RT+~200℃
- Width of guide roller
- 300mm
- substrate width
- Max.300mm
- Back roller diameter
- Ф150mm
- Reel diameter
- 3 inches.
- rewinding diameter
- Max.Ф450mm
- Applicable materials
- Lithium battery, glue, silicone oil, UV, inks, cataplasm, hot-melt adhesive, gel, plaster, Stock, etc
- Applicable substrate
- Paper, film, aluminum foil, plastic, non-woven fabric, etc
- Machine power
- 1050W
- Host power supply
- AC220V (single phase) 50Hz
- Machine size
- 1051 * 635 * 600mm (subject to actual customization)
- Machine weight
- About 120kg (subject to actual customization)
Product Introduction
The continuous coating experimental machine is a modular assembly of high-precision modular coating station mechanism, with a separable winding module, which can be added as needed, and the whole machine is fully electrically controlled, without the need for an external air source. Continuous coating proofing or low-volume production of laboratory mini hot melt adhesive coaters. The hot melt pressure-sensitive adhesive can be directly applied to the heat-resistant substrate, or coated on the release paper and then the film transfer map can be applied to different surface materials, or the single-sided coating film of the curing module can also be added. Electronically controlled precision tension control, which can adapt to the needs of different materials. Such as paper, plastic model, metal film, etc.
Configuration brief
(1) The whole machine is a high-precision modular coating station structure, which adopts modular assembly.
(2) Fully electric control, no external air supply required
(3) Use the dial indicator as the index head to accurately fine-tune the coating gap between the upper and lower rubber wheels to control the coating thickness.
(4) The minimum gluing thickness is0.01mm。 After the thickness is set, the downforce is provided by the electric actuator to prevent the gap from changing
(5) The maximum coating width is 300mm (effective coating width is 280mm). The width is adjusted by two pieces of PEEK baffles in the rubber groove. It can be coated and glued for unlimited length, and is automatically rewound.
(6) Forward and reverse stepless variable speed, coating speed: 4.5m/min (speed 2-4.5m/min adjustable), precision electronically controlled discharge reel can adjust the knob of the control panel, accurately change the discharge tension, and keep it continuously.
(7) Quick-release glue tank, the glue wheel and the rubber groove can be quickly disassembled and separated from the machine body to remove the residual glue.
Application of the product
Hot melt adhesives, gels, hydrocolloid dressings, water-based glues, solvent glues, etc